Skip to main content
Crane11 min read·

NCCCO Crane Operator Exam Practice Test: 25 Operations Questions With Explanations (OSHA Subpart CC, 2026)

Free NCCCO crane operator exam practice test: 25 operations questions on OSHA Subpart CC rules, with answers, explanations and paragraph citations for 2026.

Problem this solves

This guide solves the next-step problem for Crane candidates: it explains what matters, then gives you a direct way to test that knowledge with practice questions instead of guessing what to study next.

Overview of NCCCO and Where Operations Questions Fit

The CCO Mobile Crane Operator certification (the cards most people call NCCCO) takes a Core written exam, at least one Specialty written exam and a practical exam for each Specialty. Per the CCO Mobile Crane Operator Candidate Handbook, the Core written is 95 questions in 90 minutes with no calculator, and it is split into four domains: Site (about 22%), Operations (about 28%), Technical Knowledge (about 23%) and Load Charts (about 27%). Each Specialty written is 28 questions in 60 minutes, with a calculator, and leans harder on the manufacturer's load charts (about 35%). CCO does not publish a pass rate or a percentage cut score; scoring is criterion-referenced. Operations is the biggest single slice of the Core, and most of it comes straight out of OSHA 29 CFR 1926 Subpart CC: what the operator may and may not do, when a signal person is required, who is allowed under a load, and what happens when something goes wrong. Those rules are short, specific and very testable, which is why this practice test is built from them. Every answer below cites the OSHA paragraph it comes from, so you can check it yourself on osha.gov. If you want the site-side rules first (power lines, ground conditions, setup), take our [crane safety and site conditions practice test](/blog/nccco-crane-safety-site-conditions-practice-test-30-questions-2026). For chart math, use the [NCCCO load chart practice test](/blog/nccco-load-chart-practice-test-30-questions). This one stays on operations. These are practice questions written by VoltExam, not questions from the real exam.

Try it now — no account, no download

Practice Crane questions free

Answer 5 Crane practice questions with instant explanations before you keep reading.

Crane · Question 1 of 5

What is the definition of 'Gross Capacity' as listed in a crane's load chart?

Pick an answer to see the explanation + an instant AI breakdown.

Part 1: The Operator at the Controls (Questions 1–9)

1. The load is suspended and the operator needs to step away. Under OSHA, the operator: A) May leave if a signal person is watching B) Must not leave the controls while the load is suspended, except under specific listed conditions C) May leave for up to five minutes D) May leave once the swing brake is set Answer: B. OSHA 1926.1417(e)(1) says the operator must not leave the controls while the load is suspended unless all of the listed conditions are met. 2. Which of these is one of the required conditions in 1926.1417(e)(1) for leaving a suspended load? A) The load is under half of rated capacity B) A competent person determines it is safe and makes sure the boom hoist, telescoping, load, swing and outrigger functions are restrained C) The crane is on rubber D) The lift director signs a log Answer: B. The exceptions also require that the operator stays adjacent and is not doing other duties, that the load is held suspended longer than a normal lift, and that barricades or caution lines and notices keep people out of the fall zone. All of them must be met, not just one. 3. During a lift the operator's phone rings. OSHA's rule is: A) Phones are banned in the cab entirely B) The operator must not engage in activities that divert attention, such as cell phone use, other than when the phone is used for signal communications C) Hands-free calls are allowed D) Calls are allowed while the load is landed Answer: B. That is 1926.1417(d). A phone used as the signal channel is the exception; a personal call is not. 4. Who can give an emergency stop signal that the operator must obey? A) Only the designated signal person B) Only the lift director C) Anyone D) Only a qualified rigger Answer: C. Under 1926.1417(y), anyone who becomes aware of a safety problem must alert the operator or signal person by giving the stop or emergency stop signal, and the operator must obey it. Expect the distractor that only the signal person counts. 5. How much wire rope must stay on the drum when lowering the load or boom? A) One full wrap B) Two full wraps C) Three full wraps D) Whatever the load chart says Answer: B. 1926.1417(t): neither the load nor the boom may be lowered below the point where less than two full wraps of rope remain on their drums. Deep picks below grade, into pits or off a structure are where this gets tested. 6. When must the operator test the brakes by lifting the load a few inches and applying the brakes? A) Before every lift B) Each time a load that is 90% or more of the maximum line pull is handled C) Only on personnel lifts D) Once per shift Answer: B. That is 1926.1417(s). Note the trigger is maximum line pull, not the load chart capacity. Swapping the two is a classic trap. 7. The equipment may be operated in excess of its rated capacity when: A) A qualified person approves it B) It is a test lift C) Never; the equipment must not be operated in excess of its rated capacity D) The load is only lifted a few inches Answer: C. 1926.1417(o)(1). 8. A crane has a repair underway and a deficiency that makes it unsafe. What goes in the cab? A) Nothing, if the keys are removed B) A tag stating the equipment is out of service and not to be used C) A note in the logbook only D) A cone on the seat Answer: B. 1926.1417(f)(1) requires the out-of-service tag in the cab. 9. You find a 'do not operate' sign on the controls. You may activate the crane when: A) Your supervisor says go B) The sign has been removed by a person authorized to remove it, or you verify that no one is servicing the crane or in a dangerous position and that it has been repaired and works properly C) After a 10-minute wait D) Never on the same shift Answer: B. 1926.1417(f)(2)(i).

Free: the 20 facts Crane exams keep testing

Top 20 most-tested facts for your exam. Delivered instantly.

Part 2: Weather, Travel, Signals and the Fall Zone (Questions 10–19)

10. A local storm warning has been issued. Who decides whether to put the manufacturer's securing procedures in place? A) The operator alone B) The competent person C) The weather service D) The owner of the crane Answer: B. 1926.1417(h). 11. Wind, ice and snow are affecting the lift. Under OSHA: A) There is a fixed 20 mph limit for all crane lifts B) The competent person must adjust the equipment and/or operations to address their effect on stability and capacity C) Ice only matters on lattice booms D) Operations continue until the load chart is exceeded Answer: B. 1926.1417(n). There is no single OSHA wind speed for ordinary lifts; the manufacturer's limits and the competent person decide. (Personnel hoisting is different; see question 25.) 12. Traveling with a suspended load is: A) Always prohibited B) Prohibited if the manufacturer prohibits it; otherwise a competent person supervises and decides load position, boom location, ground support, travel route, overhead obstructions and speed C) Allowed at walking speed with no other conditions D) Allowed only on outriggers Answer: B. 1926.1417(u). 13. When does OSHA require a tag line or restraint line? A) On every lift B) When necessary to prevent rotation of the load that would be hazardous C) Only on loads over 10,000 lb D) Only in wind Answer: B. 1926.1417(w). 14. A signal person must be provided when: A) The point of operation is not in full view of the operator B) The crane is traveling and the view in the direction of travel is obstructed C) The operator or the person handling the load decides one is needed because of site-specific safety concerns D) All of the above Answer: D. Those are the three triggers in 1926.1419(a). 15. Radio signals drop out mid-swing. The operator must: A) Finish the swing slowly B) Safely stop operations until signal transmission is reestablished and a proper signal is given and understood C) Switch to horn signals D) Lower the load immediately Answer: B. 1926.1419(f). 16. While the operator is not moving a suspended load, who may be in the fall zone? A) No one at all B) Only employees hooking, unhooking or guiding the load, making the initial attachment to a component or structure, or operating a concrete hopper or bucket C) Anyone wearing a hard hat D) The signal person only Answer: B. 1926.1425(b). 17. Employees are hooking a load inside the fall zone. Which is required? A) Hooks with self-closing latches or their equivalent, materials rigged to prevent unintentional displacement, and rigging done by a qualified rigger B) A second crane on standby C) A spotter for each employee D) A tag line on every leg Answer: A. 1926.1425(c). The one listed exception is 'J' hooks used for setting wooden trusses. 18. When the load is landed, who may be in the fall zone? A) Anyone on the crew B) Only employees needed to receive the load C) Only the signal person D) No one until the hook is free Answer: B. 1926.1425(d). 19. The rotating superstructure could strike or pinch a worker. OSHA's main control is: A) A horn before every swing B) Control lines, warning lines, railings or similar barriers marking the hazard area, with warning signs and high-visibility markings where barriers are infeasible C) A second operator D) Slowing the swing Answer: B. 1926.1424(a)(2)(ii).

Part 3: Power Lines and Personnel Hoisting (Questions 20–25)

20. Before operating, the employer must determine whether any part of the equipment, load line or load could get closer than what distance to a power line, at maximum working radius? A) 10 feet B) 15 feet C) 20 feet D) 50 feet Answer: C. 1926.1408(a)(2). One of the options that follow is simply keeping 20 feet away (the '20-foot clearance' option). 21. The utility confirms a line is 69 kV. Under Table A in 1926.1408, the minimum clearance is: A) 10 feet B) 15 feet C) 20 feet D) 25 feet Answer: B. Table A: up to 50 kV, 10 feet; over 50 to 200 kV, 15 feet; over 200 to 350 kV, 20 feet. 69 kV falls in the 'over 50 to 200' row. 22. A tag line is used on a lift near a power line. It must be: A) Wire rope B) Non-conductive C) At least 20 feet long D) Held by the signal person Answer: B. 1926.1408 requires non-conductive tag lines among the measures for working near lines. 23. When hoisting personnel on a suspended platform, the total load may not exceed what share of the rated capacity for the radius and configuration (outside proof testing)? A) 25% B) 50% C) 75% D) 100% Answer: B. 1926.1431(d)(1). 24. The personnel platform trial lift is done: A) Once when the crane arrives on site B) With the unoccupied platform loaded at least to the anticipated liftweight, immediately before each shift, and again if the crane is moved or set up again or the lift route changes C) Only for lifts over 100 feet D) With the crew on board, at half speed Answer: B. 1926.1431(h)(1)-(2). 25. Which wind figure appears in OSHA's personnel hoisting rule? A) 10 mph at the boom tip B) 20 mph at the personnel platform C) 30 mph at ground level D) None; there is no wind figure in 1926.1431 Answer: B. 1926.1431(k)(8)(i) uses wind exceeding 20 mph at the personnel platform as the threshold; above it, hoisting personnel is off unless a qualified person determines it is safe. Read the full paragraph for the exact conditions. Scoring yourself: there is no official 'passing' number to compare against, because CCO does not publish one. Use this as a gap finder. Any question you missed is a paragraph to reread on osha.gov tonight.

Load Chart Basics You Still Need for Operations Questions

Operations questions often hide a load chart decision inside a rule. Question 7 is the simple version: never exceed rated capacity. The harder version asks whether a lift is inside capacity at all, which means you need the chart habits locked in. Rated capacity on a mobile crane chart depends on the configuration: outrigger position, counterweight, boom length, radius and area of operation (over the front, over the side, 360 degrees). Radius is measured horizontally from the center of rotation to the center of the hook or load, not from the outrigger or the cab. Booming down or letting the boom deflect increases radius and cuts capacity, which is why a load that was fine at pick-up can be over the chart at set-down. The number in the chart is gross capacity. Net capacity is what is left after the chart's deductions, typically the hook block, the rigging and any stowed or erected jib, as the chart notes direct. When the radius or boom length falls between chart values, follow the chart notes; most manufacturers tell you to use the next longer radius or boom length rather than interpolating. Practice the full sequence on the [crane load calculator](/tools/crane-load) until it takes under a minute.

Rigging Math in 60 Seconds

The Core exam has no calculator, so rigging math has to be quick and approximate. The one formula worth memorizing: tension per leg of a symmetrical two-leg bridle = (load ÷ 2) ÷ sin(sling angle from horizontal). Example: a 6,000 lb load on a two-leg bridle at 60 degrees. Each leg carries 3,000 ÷ 0.866 ≈ 3,464 lb. At 45 degrees the same legs carry about 4,243 lb each; at 30 degrees, 6,000 lb each, double the straight vertical share. Memorize the multipliers instead of the trig: about 1.15 at 60 degrees, 1.41 at 45 degrees and 2.0 at 30 degrees. Two other habits pay off: add the rigging and block weight to the load before comparing with the chart, and remember that question 17 is a rigging question in disguise. Hooks with self-closing latches and a qualified rigger are what make hooking inside the fall zone legal. For a deeper walkthrough, read [NCCCO rigging math: sling angles and net capacity](/blog/nccco-rigging-math-sling-angles-net-capacity-2026).

Practical Exam Tips That Come From These Same Rules

The CCO practical covers hands-on inspection, hoisting, booming, swinging, hand signals and combined operations with and without a load, per the candidate handbook. Many of the written rules above show up again in how examiners watch you work. Treat the stop signal as sacred: if an examiner or anyone else gives it, stop, no matter where the load is. Keep your eyes on the load and the signals; anything that looks like a divided attention habit costs you. Watch your hook height so you never approach two-blocking, and keep the load path smooth so you are not swinging a pendulum into the target zone. Do your walk-around like you mean it and say what you are checking out loud. And if communication breaks down, stop and reestablish it rather than guessing. That is the correct answer on the written and the correct move on the practical. Our [NCCCO practical exam guide](/blog/nccco-practical-exam-crane-operator-skills-test-2026) walks through the tasks.

Study Strategy: Turn the OSHA Paragraphs Into Points

Operations questions reward people who know exactly who decides what. Build a three-column sheet: the situation (storm warning, travel with load, leaving the controls, wind and ice), the person who decides (operator, competent person, qualified person, anyone), and the paragraph. Most wrong answers on the real exam swap the decision maker or the trigger (line pull versus rated capacity, two wraps versus three, 50% versus 75%). Then work in short daily sets. Ten questions a day, reviewed the same day, beats a weekend cram, and it fits around a full work schedule. Keep a miss list and reread the matching OSHA paragraph for each miss. Use the [crane study plan](/study/crane) to pace Site, Operations, Technical Knowledge and Load Charts in proportion to their weight on the Core, and drill free questions at [/questions/crane](/questions/crane). Finally, read the actual standard at least once. Subpart CC is long, but 1926.1417, 1926.1419, 1926.1424, 1926.1425, 1926.1408 and 1926.1431 cover nearly everything in this test. OSHA 1926.1427 is the section that requires operator certification or qualification in the first place, and it is worth knowing for the 'why am I here' questions.

Download the Crane Prep App

Download the Crane Prep app for timed NCCCO-style practice across operations, load charts, rigging, signals and site conditions, with explanations for every answer. See what is included on the [Crane Prep page](/apps/crane), and try free NCCCO practice questions on VoltExam at [/questions/crane](/questions/crane) before you commit. Digital practice supports, but does not replace, hands-on training and seat time on the crane type you are testing on.

Sources

CCO Mobile Crane Operator Candidate Handbook (exam structure, domains, scoring, validity, recertification): https://www.nccco.org/docs/default-source/2025/mobile-crane-operator-candidate-handbook_111424---en.pdf?sfvrsn=e5e8c20e_2 OSHA 1926.1417 Operation: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1417 OSHA 1926.1419 Signals, general requirements: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1419 OSHA 1926.1424 Work area control: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1424 OSHA 1926.1425 Keeping clear of the load: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1425 OSHA 1926.1408 Power line safety (up to 350 kV): https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1408 OSHA 1926.1431 Hoisting personnel: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1431 OSHA 1926.1427 Operator training, certification and evaluation: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1427

Free Crane Tools

AI

Studying with VoltAI

Stuck on a Crane question? Ask VoltAI why.

VoltAI is a built-in AI tutor that explains every practice answer in plain language — citing the actual code, protocol, or standard — and answers your follow-ups until it clicks. Most prep apps just tell you the right letter; VoltAI teaches the reasoning the exam actually tests, so you pass by understanding, not memorizing. Free to try, no account.

Try VoltAI free →

Your next best step

Turn this guide into practice

Use the article to understand the topic, then do a short web practice session to find your weak spots. Paid web access is optional after the free preview.

This article is for educational purposes only. VoltExam is not affiliated with or endorsed by any licensing body, exam organization, or government agency. All trademarks belong to their respective owners. Full disclaimer