Skip to main content
Crane12 min read·

NCCCO Technical Knowledge Practice Test: 25 Crane Operator Exam Questions With Explanations (2026)

Free NCCCO Technical Knowledge practice test: 25 crane operator exam questions on wire rope, operational aids, inspections and assembly, with OSHA citations.

Problem this solves

This guide solves the next-step problem for Crane candidates: it explains what matters, then gives you a direct way to test that knowledge with practice questions instead of guessing what to study next.

Overview of NCCCO and Where Technical Knowledge Fits

The CCO Mobile Crane Operator certification (what most people still call NCCCO) takes a Core written exam, at least one Specialty written exam and a practical exam for each Specialty. Per the CCO Mobile Crane Operator Candidate Handbook, the Core written exam is 95 questions in 90 minutes with no calculator, split into four domains: Site (about 22%), Operations (about 28%), Technical Knowledge (about 23%) and Load Charts (about 27%). Each Specialty written exam is 28 questions in 60 minutes with a calculator, and Technical Knowledge is about 19% of it. CCO does not publish a pass rate or a percentage cut score; scoring is criterion-referenced. Technical Knowledge is the domain where people who run cranes every day still drop points, because it asks about the machine itself and the rules for keeping it fit to run: wire rope condition, the operational aids in the cab, inspections, assembly and setup, and the mechanics of reeving. Most of those rules live in OSHA 29 CFR 1926 Subpart CC, sections 1926.1402, 1926.1404, 1926.1412, 1926.1413 and 1926.1416. Every answer below cites the paragraph it comes from, so you can check it on osha.gov. This is the third practice test in the series. For operator duties, signals and power lines, take the [NCCCO Operations practice test](/blog/nccco-crane-operator-exam-operations-practice-test-25-questions-osha-subpart-cc-2026). For chart math, use the [NCCCO load chart practice test](/blog/nccco-load-chart-practice-test-30-questions). These are practice questions written by VoltExam, not questions from the real exam, and the topic mix is our own choice, not CCO's published outline.

Try it now — no account, no download

Practice Crane questions free

Answer 5 Crane practice questions with instant explanations before you keep reading.

Crane · Question 1 of 5

What is the definition of 'Gross Capacity' as listed in a crane's load chart?

Pick an answer to see the explanation + an instant AI breakdown.

Part 1: Wire Rope Inspection and Removal (Questions 1–8)

1. Who performs the shift inspection of wire rope? A) The crane owner B) A competent person C) A registered professional engineer D) The manufacturer's representative Answer: B. OSHA 1926.1413(a)(1) requires a competent person to inspect the rope before each shift; the inspection can be completed during the shift. Untwisting the rope or booming down is not required for it. 2. On a running rope, which finding is a Category II deficiency? A) Six randomly distributed broken wires in one rope lay B) One broken wire anywhere on the rope C) Light surface rust D) Fresh lubricant on the rope Answer: A. 1926.1413(a)(2)(ii)(A)(1): six randomly distributed broken wires in one rope lay, or three broken wires in one strand in one rope lay. 3. For rotation-resistant rope, the Category II broken-wire criterion is: A) Six in one lay B) Two randomly distributed broken wires in six rope diameters, or four in 30 rope diameters C) Any broken wire at all D) Ten in one lay Answer: B. 1926.1413(a)(2)(ii)(A)(2). Rotation-resistant rope gets a stricter count because its inner layers can fail where you cannot see them. 4. A rope measures more than 5% under its nominal diameter. That is: A) Normal wear, no action needed B) A Category II deficiency C) Only a concern on boom hoist ropes D) Acceptable if the rope is lubricated Answer: B. 1926.1413(a)(2)(ii)(B). Loss of diameter points to core failure, internal wear or corrosion. 5. You find birdcaging on the hoist rope during your shift inspection. Under OSHA this is: A) A Category I item that the competent person must assess for an immediate hazard B) Cosmetic C) Only a problem on standing ropes D) Something to note at the next annual inspection Answer: A. 1926.1413(a)(2)(i)(A) lists significant distortion, including kinking, crushing, unstranding, birdcaging and core protrusion. Under (a)(4)(i) the competent person decides right away whether it is a hazard; if it is, operations stop until the rope is replaced or the damaged section is severed. 6. A hoist rope has touched an energized power line. What happens to it? A) It can be spliced and returned to service B) It is a Category III deficiency; repairing it is prohibited C) It is fine if no wires look burned D) It only needs a monthly inspection Answer: B. 1926.1413(a)(2)(iii)(B) makes prior power line contact a Category III deficiency, and (a)(4)(iii) prohibits repairing rope that contacted an energized power line. 7. Localized rope damage is fixed by cutting the rope. Which statement is correct? A) The two ends may be spliced back together B) Splicing is prohibited, and the drum must keep two wraps when the load or boom is at its lowest point C) The drum may run empty as long as the load is light D) Any rope length is acceptable after cutting Answer: B. 1926.1413(a)(4)(i)(B) allows severing the rope in two, prohibits splicing, and requires two wraps on the drum at the lowest load or boom position. 8. Who performs the annual wire rope inspection, covering the full length of the rope? A) The operator, at the start of the shift B) A qualified person C) Any crew member D) The rope manufacturer only Answer: B. 1926.1413(c)(1) and (c)(2): at least every 12 months, a qualified person inspects the rope, including normally hidden sections, reverse bends and the sections that pass over sheaves. Equipment with a rope deficiency is tagged out until it is fixed (1926.1413(a)(4)(iv)).

Free: the 20 facts Crane exams keep testing

Top 20 most-tested facts for your exam. Delivered instantly.

Part 2: Operational Aids (Questions 9–15)

9. Which of these is a Category I operational aid under OSHA? A) Boom angle indicator B) Anti two-blocking device C) Boom length indicator D) Hoist drum rotation indicator Answer: B. 1926.1416(d) lists the boom hoist limiting device, the luffing jib limiting device and the anti two-blocking device as Category I. The others are Category II under 1926.1416(e). 10. A Category I operational aid stops working. How long does the employer have to repair it? A) 24 hours B) 7 calendar days, or 7 days after receiving parts ordered within those 7 days C) 30 calendar days D) Until the next annual inspection Answer: B. 1926.1416(d). 11. A Category II operational aid stops working. The repair deadline is: A) 7 calendar days B) 30 calendar days, with an extension to 7 days after receipt if parts ordered within 7 days have not arrived C) 90 days D) There is no deadline Answer: B. 1926.1416(e). 12. The boom angle indicator is out while it waits for repair. What temporary measure does OSHA allow? A) The operator estimates the angle by eye B) Measuring the radius or boom angle with a measuring device C) Running at 50% of chart capacity D) No lifts at all Answer: B. 1926.1416(e)(1). The boom angle or radius indicator must normally be readable from the operator's station. 13. The load moment indicator (LMI/RCI) fails on a crane rated over 6,000 lb, built after March 29, 2003. What temporary measure applies? A) Lift only at night B) The load weight is determined from a reliable source or by calculation and given to the operator before the lift C) Bypass the system and continue D) Reduce the boom length by half Answer: B. 1926.1416(e)(4)(i). Note the temporary measure is about knowing the load weight, not disabling the device. 14. The boom hoist limiting device is out of service. Which is an allowed temporary measure? A) Using a boom angle indicator, or marking the boom hoist cable so the operator or a spotter can see the limit B) Having a laborer hold the boom C) Operating only with the boom fully lowered D) None; the crane must be parked Answer: A. 1926.1416(d)(1)(i) lists a boom angle indicator, cable marking visible to the operator (with mirrors or cameras if needed), or cable marking with a spotter. At least one must be used. 15. An operational aid stops working in the middle of a lift sequence. What does OSHA require? A) Finish the shift, then report it B) Stop operations until the temporary measures are in place or the device works again C) Keep going if the load is under 75% of capacity D) Ask the signal person to watch more closely Answer: B. 1926.1416(c). Under 1926.1416(b), operations may not even start unless the listed aids work, except during a repair window with the temporary measures in place.

Part 3: Inspections, Assembly and Setup (Questions 16–25)

16. The shift inspection of the crane (not just the rope) must be done: A) By a qualified person, once a week B) By a competent person, begun before each shift and completed before or during that shift C) By the operator only after a problem appears D) Only after assembly Answer: B. 1926.1412(d)(1). It includes items like wire rope, ground conditions, and safety devices and operational aids. Taking components apart or booming down is not required unless needed. 17. How long must the monthly inspection record be kept? A) One week B) A minimum of three months C) Five years D) It does not need to be written down Answer: B. 1926.1412(e)(3) requires the items checked, results, and the inspector's name, signature and date, kept for at least three months. 18. The annual/comprehensive inspection is done by: A) A competent person, with records kept 30 days B) A qualified person, with records kept at least 12 months C) The operator, with no record D) The crane rental company, with no record Answer: B. 1926.1412(f)(1) and (f)(7). 19. A crane has sat idle for three months or more. Before it is used again: A) Nothing special is required B) A qualified person must do an inspection that meets the monthly inspection requirements C) Only the batteries need charging D) The operator runs it at half capacity for one day Answer: B. 1926.1412(h). 20. Who can serve as the assembly/disassembly (A/D) director? A) Anyone on the crew B) Someone who meets the criteria for both a competent person and a qualified person, or a competent person assisted by one or more qualified persons C) Only a registered professional engineer D) Only the crane owner Answer: B. 1926.1404(a)(1). 21. Boom section pins are being removed during disassembly. Where must workers stay? A) Directly under the boom, to catch the section B) Out from under the boom, jib or other components, unless site constraints make that impossible and the A/D director has put special procedures in place C) Anywhere, as long as they wear a hard hat D) Inside the cab Answer: B. 1926.1404(f)(1) and (f)(2). Boom sections and suspension systems must also be rigged or supported to stay stable when pins come out (1926.1404(h)(7)). 22. When outriggers are used, OSHA requires them to be: A) Partly extended to save room B) Fully extended, or deployed as the load chart specifies if the manufacturer allows, and set so the crane's weight is off the wheels C) Extended only on the side of the lift D) Left retracted for lifts under 10 tons Answer: B. 1926.1404(q)(1) and (q)(2). Each outrigger must also be visible to the operator or a signal person while it is extended and set (q)(4). 23. Where may blocking go under an outrigger? A) Anywhere under the beam B) Only under the outrigger float or pad, or, if there is no jack, under the outer bearing surface of the extended beam C) Under the tires D) Blocking is not allowed under outriggers Answer: B. 1926.1404(q)(5). 24. Under OSHA, 'ground conditions' means: A) The weather on site B) The ability of the ground to support the equipment, including slope, compaction and firmness C) The paving type only D) The distance to the nearest power line Answer: B. 1926.1402(a)(1). Under 1926.1402(c), the controlling entity must provide the ground preparation needed and tell the operator about known hazards beneath the setup area, such as voids, tanks and utilities. 25. A 20,000 lb load (including the hook block and rigging) hangs on four parts of line. Ignoring sheave friction, about how much pull is on each part of line? A) 2,000 lb B) 5,000 lb C) 10,000 lb D) 20,000 lb Answer: B. Divide the total load by the parts of line: 20,000 ÷ 4 = 5,000 lb. Real reeving adds friction losses, so the manufacturer's line pull rating and reeving chart decide the actual parts of line needed. This one is VoltExam's own mechanics question, not an OSHA rule.

Load Chart Basics That Show Up in Technical Questions

Technical Knowledge questions often sit right next to a load chart decision. The aids in Part 2 exist because the chart only works if you know your radius, boom angle, boom length and load weight. Lose the boom angle indicator and you lose your radius; lose the LMI and you lose your weight check. That is why the temporary measures OSHA allows are all about measuring or calculating those same numbers. Rated capacity on a mobile crane chart depends on configuration: outrigger position, counterweight, boom length, radius and area of operation. Radius is measured horizontally from the center of rotation to the center of the hook or load. The chart number is gross capacity; net capacity is what remains after the deductions the chart notes call for, usually the hook block, rigging and any stowed or erected jib. When radius or boom length falls between chart values, follow the chart notes; most manufacturers tell you to use the next longer value rather than interpolate. Practice the sequence on the [crane load calculator](/tools/crane-load).

Rigging Math in 60 Seconds

The Core exam has no calculator, so the math has to be quick. Two formulas cover most of it. Parts of line: line pull per part ≈ total load ÷ parts of line (before friction). A 20,000 lb load on four parts is about 5,000 lb per part. In an illustrative case where the hoist line is rated for 7,000 lb of line pull, three parts would put about 6,667 lb on each part, close to the limit before friction is added. That is why reeving charts usually call for more parts than the bare division suggests. Two-leg bridle: tension per leg = (load ÷ 2) ÷ sin(sling angle from horizontal). Memorize the multipliers instead of the trig: about 1.15 at 60 degrees, 1.41 at 45 degrees and 2.0 at 30 degrees. A 6,000 lb load at 60 degrees puts about 3,464 lb on each leg. Always add the block and rigging weight to the load before you compare it with the chart. For more practice, read [NCCCO rigging math: sling angles and net capacity](/blog/nccco-rigging-math-sling-angles-net-capacity-2026).

Practical Exam Tips From the Same Rules

The CCO practical covers hands-on inspection, hoisting, booming, swinging, hand signals and combined operations with and without a load, per the candidate handbook. The inspection piece is Technical Knowledge you do with your hands. Do your walk-around the way 1926.1412(d) describes it: rope, hook and latch, sheaves, hydraulics, tires or tracks, outriggers and pads, ground conditions, and the operational aids in the cab. Say out loud what you are checking. Test the anti two-block function and look at the boom angle indicator before you lift. Watch your drum so you never run it close to empty, and keep the hook block well clear of the boom tip. Our [NCCCO practical exam guide](/blog/nccco-practical-exam-crane-operator-skills-test-2026) walks through the tasks, and the [wire rope inspection guide](/blog/nccco-crane-wire-rope-inspection-removal-criteria-osha-1926-1413-2026) goes deeper on what to look for.

Study Strategy: Learn the Categories, Not Just the Facts

Technical Knowledge rewards people who can sort things into buckets. Build three short tables. Wire rope: Category I (distortion, corrosion, heat damage, bad end connections), Category II (broken-wire counts, more than 5% diameter loss) and Category III (core failure in rotation-resistant rope, power line contact, a broken strand). Operational aids: Category I (boom hoist limiter, luffing jib limiter, anti two-block, 7 days) and Category II (angle, length, load and position indicators, 30 days), each with its temporary measure. Inspections: shift (competent person), monthly (records three months), annual (qualified person, records 12 months), idle three months or more. Most wrong answers swap one bucket for another: competent for qualified, 7 days for 30, three months for 12. Drill ten questions a day and reread the OSHA paragraph for every miss. Use the [crane study plan](/study/crane) to balance Site, Operations, Technical Knowledge and Load Charts by their weight on the Core, and practice free at [/questions/crane](/questions/crane). If you have not done the setup side yet, the [crane safety and site conditions practice test](/blog/nccco-crane-safety-site-conditions-practice-test-30-questions-2026) and the [outrigger and ground bearing guide](/blog/nccco-crane-outrigger-loads-ground-bearing-pressure-setup-math-2026) pair well with Part 3.

Download the Crane Prep App

Download the Crane Prep app for timed NCCCO-style practice on load charts, rigging, wire rope, operational aids, signals and site conditions, with explanations for every answer. See what is included on the [Crane Prep page](/apps/crane), and try free NCCCO practice questions on VoltExam at [/questions/crane](/questions/crane). Digital practice supports, but does not replace, hands-on training and seat time on the crane type you are testing on.

Sources

CCO Mobile Crane Operator Candidate Handbook (exam structure, domains, scoring, validity, recertification): https://www.nccco.org/docs/default-source/2025/mobile-crane-operator-candidate-handbook_111424---en.pdf?sfvrsn=e5e8c20e_2 OSHA 1926.1402 Ground conditions: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1402 OSHA 1926.1404 Assembly/Disassembly: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1404 OSHA 1926.1412 Inspections: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1412 OSHA 1926.1413 Wire rope inspection: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1413 OSHA 1926.1416 Operational aids: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1416 OSHA 1926.1427 Operator training, certification and evaluation: https://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.1427

Free Crane Tools

AI

Studying with VoltAI

Stuck on a Crane question? Ask VoltAI why.

VoltAI is a built-in AI tutor that explains every practice answer in plain language — citing the actual code, protocol, or standard — and answers your follow-ups until it clicks. Most prep apps just tell you the right letter; VoltAI teaches the reasoning the exam actually tests, so you pass by understanding, not memorizing. Free to try, no account.

Try VoltAI free →

Your next best step

Turn this guide into practice

Use the article to understand the topic, then do a short web practice session to find your weak spots. Paid web access is optional after the free preview.

This article is for educational purposes only. VoltExam is not affiliated with or endorsed by any licensing body, exam organization, or government agency. All trademarks belong to their respective owners. Full disclaimer